What the classroom noise meter does
The tool above listens through your device's microphone and shows how loud the room is, live. It is built for the front of a classroom: large, simple and readable from the back row.
- Four display themes. Bar (a level bar that fills as the room gets louder), Traffic light (green, yellow, red), Face (an emoji that reacts to the noise) and Big number (the level in decibels).
- Sensitivity slider. Makes the display react more or less strongly, so it suits a small quiet group or a full, lively room.
- "Too loud" limit line. Drag the line or set a value. Everything above it counts as too loud.
- "Too loud" counter. Counts how many times the class went over the limit, which is handy for class goals.
- Optional "shh" sound. Plays when the limit is exceeded. It is off unless you turn it on.
- Fullscreen. One click fills the projector or smartboard.
- Shareable settings link. Your theme, sensitivity and limit are saved in a link you can bookmark or send to a colleague.
- Nothing recorded or uploaded. Sound is measured on your device and never leaves it. See our privacy policy.
How to set it up in class
- Open this page on the computer that drives your projector or smartboard and allow microphone access when the browser asks.
- Place the microphone sensibly. A laptop on your desk near the middle of the room works better than one next to a fan, an open window or the projector's own speaker. Keep it in the same spot each day so readings stay comparable.
- Pick a theme. The traffic light and face are easiest for younger students. Older students often prefer the bar or the number.
- Run a calibration minute. Ask the class to work for one minute at the level you actually want, such as partner voices. Watch where the reading sits most of the time.
- Set the limit just above that level. Drag the "too loud" line a little higher than the readings from your calibration minute. If it trips on every chair scrape, raise it slightly or lower the sensitivity.
- Go fullscreen and bookmark the settings link so tomorrow starts with the same setup.
A calibration minute is about finding a fair limit for your room. It is different from calibrating the meter against a reference instrument, which we explain on the calibration page.
Suggested classroom levels
Many schools use a 0 to 4 voice-level chart. The table maps those levels to approximate meter readings. This is a rule of thumb, not a standard. A full room whispering is louder than one whisper, and an uncalibrated microphone can read several decibels high or low. Use the numbers as a starting point and trust your calibration minute.
| Voice level | What it means | Typical activity | Rough room reading |
|---|---|---|---|
| 0 | Silent | Tests, silent reading | about 35–45 dB |
| 1 | Whisper | Independent work, library time | about 45–55 dB |
| 2 | Partner or table talk | Pair and small-group work | about 55–65 dB |
| 3 | Presenter voice | One speaker to the whole class | about 65–75 dB |
| 4 | Outside voice | Recess, gym | 75 dB and up |
Some reference points behind these ranges: the U.S. National Institute on Deafness and Other Communication Disorders puts normal conversation at 60–70 dBA. The classroom acoustics standard ANSI/ASA S12.60 sets a design limit of 35 dBA for background noise in an empty typical classroom, and the World Health Organization's community noise guidelines also recommend 35 dB during teaching so that speech is easy to understand. An occupied room will always sit above that. For a wider comparison, see the decibel chart.
Routines that work
- Name the target before the task. "This is a level 2 activity" plus a visible limit line tells students exactly what is expected.
- Let students watch it. The point of a visual meter is self-monitoring. Give a table group the job of "noise captains" for the lesson.
- Use the counter for a class goal. For example: "Fewer than five times over the line during this 20-minute work block." Reset the counter between activities.
- Keep the "shh" sound for when you need it. A constant sound cue loses its effect quickly. Many teachers leave it off and let the color change do the work.
- Don't make it a game to beat. If students start shouting to move the bar, switch to the traffic light, lower the sensitivity, or hide the display for a few minutes.
Group work and testing
Group work. Productive talk is the goal, so set the limit generously. Run your calibration minute while groups are working well, then set the line a little above it. The meter then only flags the moments when the room really gets out of hand.
Tests and silent reading. Lower the limit and raise the sensitivity so that small sounds register. Turn the "shh" sound off, since a sound cue interrupts everyone. The big number or bar theme is the least distracting here.
Accessibility: a signal every student can see
A visual noise signal helps students who do not pick up on verbal reminders, including many deaf and hard-of-hearing students, students with attention or sensory-processing differences, and students who are still learning English. A few tips:
- The traffic light uses position as well as color, and the face and bar themes do not rely on color at all. Choose one of these if you have color-blind students.
- Noise-sensitive students may find a sudden "shh" sound unpleasant. Leave it off or warn the class first.
- The meter shows the loudness of the room, not of any one student. Use it as a shared signal for the class, never to single someone out.
How accurate is it?
For classroom management you only need a consistent relative signal, and any working microphone gives you that. The number itself is an estimate. Read more on our accuracy page, or use the full decibel meter if you want weighting, averages and a graph. The classroom meter is a teaching aid and is not meant for assessing hearing risk. See safe decibel levels.
Sources
- NIDCD: Noise-Induced Hearing Loss (typical sound levels, including normal conversation at 60–70 dBA)
- ANSI: ANSI/ASA S12.60-2010/Part 1 (R2020), acoustical performance criteria for schools
- World Health Organization: Guidelines for Community Noise (1999)
Frequently asked questions
Is the classroom noise meter free?
Yes. It runs in the browser with no account, no download and no time limit.
Does it record my students?
No. The microphone signal is turned into a loudness number on your device and then discarded. No audio is recorded, stored or uploaded.
What decibel level should a classroom be?
There is no single correct number, because readings depend on your device, where it sits and the room. As a rough guide, quiet independent work often reads around 40 to 50 dB and group work around 55 to 65 dB. Run a calibration minute to find the right limit for your own room.
Does it work on a smartboard or Chromebook?
Yes. It works in current versions of Chrome, Edge, Safari and Firefox on any device with a microphone. If your board has no microphone, run the meter on a laptop and mirror or cast the screen.
Why does the meter show a different number than my phone?
Every microphone has a different sensitivity, so two uncalibrated devices rarely agree. For classroom routines only the relative level matters: quieter or louder than your limit.
How do I keep the same settings every day?
Use the shareable settings link. It stores your theme, sensitivity and limit in the address, so you can bookmark it and open the meter ready to go.
Updated