How to use the test
- Turn the volume down first, especially with headphones, then raise it to a comfortable level.
- Press Left. Sound should come only from the left speaker or earbud, and the left channel lights up on screen. Then press Right.
- Press Center. Both channels play together. On speakers the sound should seem to come from a point midway between them. On headphones it should sit in the middle of your head.
- Press Alternate to loop left, then right, while you move cables or adjust settings.
- Pick a signal. Pink noise has equal energy in every octave, which makes it easy to locate and good for comparing the loudness of the two sides. The 440 Hz tone is a simple reference. The chirp sweeps across frequencies and shows up rattles and missing bass or treble.
If left and right are swapped
- Headphones and earbuds: check the L and R markings and that each one is in the correct ear.
- Desktop speakers: swap their positions, or swap the left and right plugs at the amplifier or sound card.
- Adapters and splitters: a worn or partly inserted 3.5 mm plug can swap, merge or drop a channel. Push it in fully or try another cable.
If you hear both sides at once, or one side is silent
The usual cause is a mono audio or balance setting. These live in the sound or accessibility settings. Menu names vary a little between versions.
| System | Balance (left/right level) | Mono audio |
|---|---|---|
| Windows 11 | Settings > System > Sound, select the output device, then set the Left and Right channel sliders to the same level | Settings > System > Sound, "Mono audio" toggle in the Output section (also under Settings > Accessibility > Audio) |
| macOS | Apple menu > System Settings > Sound > Output, select the device, then drag the Balance slider | System Settings > Accessibility > Audio, "Play stereo audio as mono" |
| iPhone and iPad | Settings > Accessibility > Audio & Visual, Balance slider | Same screen, "Mono Audio" |
| Android | Settings > Accessibility > Audio adjustment, "Audio balance" slider | Same screen, "Mono audio" (the section name differs between phone makers) |
For a stereo test, mono audio should be off and the balance slider centered. Mono audio is an accessibility feature for people who hear better in one ear, so only change it on your own device.
Bluetooth headphones and earbuds
- Battery. Some headsets and earbuds switch one side off or reduce function when its battery is low. Charge both.
- Re-pair. Remove the device from your Bluetooth list and pair it again, making sure both earbuds connect. A single earbud that paired on its own will play everything in one ear.
- Firmware. Check the maker's app or website for an update.
- Cross-check. Try the headphones on another device. If the problem follows them, the fault is in the hardware.
When one side is quieter
- Play pink noise and switch between Left and Right. Small differences are easier to hear with noise than with a tone.
- Center the balance slider (see the table above).
- Swap the earbuds between ears, or turn the headphones around. If the quiet side moves with the earbud, the cause is the hardware: a blocked mesh, a loose plug, a weak battery or a failing driver. Clean the mesh gently as the maker recommends and check the fit of the ear tip.
- If the same ear stays quiet whichever earbud is in it, the difference may be in your hearing. That is worth mentioning to a doctor or audiologist. This test cannot diagnose it.
With loudspeakers, you can compare the two sides with the decibel meter at your listening position: play pink noise on each channel in turn and note the readings.
Polarity (phase) test
If one speaker of a pair is connected with its positive and negative wires reversed, its cone moves in while the other moves out. Both still play, but low frequencies partly cancel and the stereo image falls apart.
The polarity test plays the same signal on both channels, first in phase and then out of phase. Sit midway between the speakers:
- Wired correctly: the in-phase signal sounds focused in the center with full bass. The out-of-phase signal sounds wide, vague and thin.
- One speaker reversed: the opposite. The "out of phase" signal sounds more solid.
To fix it, switch the amplifier off and swap the two wires on one speaker so that + goes to + and − goes to − on both. Reversed polarity does not damage anything.
Related tools
Use the tone generator for single frequencies and bass sweeps, the spectrum analyzer to see what your speakers put out, and safe decibel levels for how loud headphone listening should be.
Sources
- Microsoft Support: Fix Bluetooth audio only playing in one channel (balance, mono audio, battery, re-pairing)
- Apple Support: Change the sound output settings on Mac (Balance slider)
- Apple Support: Change Audio settings for accessibility on Mac (Play stereo audio as mono)
- Apple Support: iPhone User Guide, mono audio and balance
- Sony Help Guide (Android): Accessibility settings, Audio adjustment
- Sound & Vision: How do I diagnose phase problems in my system?
- Live Science: What is pink noise? (equal energy per octave)
Frequently asked questions
How do I test left and right audio?
Press the Left button and check that sound comes only from the left speaker or earbud, then press Right. Alternate loops between the two sides so you can listen hands-free.
Why do I hear sound from both sides when I press Left?
Your device is probably set to mono audio, which mixes both channels into each side. Turn mono audio off in the sound or accessibility settings. Some Bluetooth speakers and single phone speakers are mono by design.
Why is one headphone side quieter than the other?
Common causes are a balance slider that is off center, a blocked earbud mesh, a poor fit, a partly inserted plug, or a low battery in one wireless earbud. Swap the earbuds between ears to see whether the quiet side follows the earbud.
How do I know if my speakers are out of phase?
Run the polarity test. With correct wiring, the in-phase signal sounds focused between the speakers with full bass, and the out-of-phase signal sounds diffuse with weak bass. If it is the other way around, one speaker is wired backwards.
Which test signal should I use?
Pink noise is best for locating a channel and comparing loudness. The 440 Hz tone is easy to hear but harder to localize. The chirp sweeps through frequencies and reveals rattles or a dead driver.
Does the test work with Bluetooth headphones?
Yes. If one side is silent, check its battery, turn mono audio off, and remove and re-pair the headphones so both earbuds connect.
Updated