How to read the slider
Move the slider above from 0 to 140 dB and four values change together. They are four ways of describing the same sound.
| Readout | Formula | At 60 dB | At 100 dB |
|---|---|---|---|
| Intensity relative to the threshold of hearing | 10^(L/10) | 1,000,000× | 10,000,000,000× |
| Sound pressure | 20 µPa × 10^(L/20) | 0.02 Pa | 2 Pa |
| Perceived loudness relative to 60 dB | 2^((L − 60)/10) | 1× | about 16× |
| Nearest example sound | from our decibel chart | normal conversation (60–70 dBA) | concerts and sporting events (94–110 dBA) |
Slide from 60 to 100 dB and the intensity grows ten-thousandfold while the perceived loudness grows about sixteenfold. That mismatch between the physics and the experience is the whole reason the scale exists.
Why sound uses a logarithmic scale
There are two reasons, one practical and one about hearing.
- The range is enormous. The intensity at the threshold of pain is about ten trillion (1013) times the intensity at the threshold of hearing. In ordinary units, a whisper and a siren would need numbers with wildly different counts of zeros. On the decibel scale they are about 30 and 110 to 129.
- Hearing responds to ratios. Going from one violin to two is a clear change. Going from ten to eleven is hardly noticeable, although the same amount of sound was added. Equal steps in decibels correspond much more closely to equal steps in what we hear.
The definition is short. For intensity, L = 10 × log10(I / I0). For pressure, L = 20 × log10(p / p0). The factor of 20 appears because intensity is proportional to pressure squared. The decibel definition page works through the formulas.
The three rules: +3, +6 and +10 dB
| Change | Intensity (energy) | Sound pressure | Perceived loudness |
|---|---|---|---|
| +3 dB | ×2 | ×1.41 | Noticeable |
| +6 dB | ×4 | ×2 | Clearly louder |
| +10 dB | ×10 | ×3.16 | About twice as loud |
| +20 dB | ×100 | ×10 | About four times as loud |
- +3 dB doubles the energy.
10 × log10(2)= 3.01. This is why NIOSH halves the recommended exposure time for every 3 dB, as explained on safe decibel levels. - +6 dB doubles the pressure.
20 × log10(2)= 6.02. It is also why the level falls by about 6 dB when you double your distance from a small source outdoors. - +10 dB sounds about twice as loud. This one is different in kind. The first two are exact mathematics; this is a finding about human perception. Georgia State University's HyperPhysics calls it an approximate general statement, "not to be taken as a hard and fast rule". The real figure depends on the listener, the frequency and the level.
What 0 dB means: the 20 µPa reference
A decibel value is always relative to a reference. For sound in air the reference pressure is 20 micropascals (20 µPa, or 0.00002 Pa), about the faintest 1,000 Hz tone a healthy young person can hear. Levels measured against it are written dB SPL (sound pressure level). The matching intensity reference is 10−12 watts per square meter.
Some fixed points on the scale follow from that reference:
- 0 dB = 20 µPa, the threshold of hearing
- 60 dB = 0.02 Pa, around normal conversation
- 94 dB = 1 Pa, a standard calibrator level
- 120 dB = 20 Pa, near the threshold of pain
- 140 dB = 200 Pa, the peak level that workplace rules say impulse noise should not exceed
Even 200 Pa is small next to normal atmospheric pressure of about 101,325 Pa. Sound is a tiny ripple on top of the air pressure around us, and the ear is sensitive enough to detect it.
Adding decibels
Decibel values cannot be added like ordinary numbers. Convert each level to intensity, add the intensities and convert back:
Ltotal = 10 × log10(10^(L1/10) + 10^(L2/10))
| Sources | Combined level | Why |
|---|---|---|
| 60 dB + 60 dB | 63 dB | Double the energy adds 3 dB |
| 60 dB + 54 dB | 61 dB | The quieter source adds about 1 dB |
| 60 dB + 50 dB | 60.4 dB | A source 10 dB lower adds almost nothing |
| Ten sources of 60 dB | 70 dB | Ten times the energy adds 10 dB |
The practical lesson: the loudest source dominates. Silencing the second-loudest machine in a room barely changes the total. The decibel calculator adds and subtracts any set of levels for you. The same energy logic explains why an average level (Leq) sits close to the loud moments of a recording and not midway between loud and quiet.
Common misconceptions
- "0 dB is silence." It is the reference level. A sound with a pressure below 20 µPa has a negative decibel value.
- "80 dB is twice as loud as 40 dB." It has 10,000 times the intensity and, by the rule of thumb, sounds about 16 times as loud.
- "Twice the power means twice the loudness." Doubling the power adds only 3 dB, a noticeable but modest change. A tenfold increase is needed for a sound to seem about twice as loud.
- "A few decibels do not matter." For hearing safety they do. Each 3 dB halves the recommended exposure time, so 94 dBA allows one hour where 85 dBA allows eight.
- "A decibel is a fixed amount of sound." It is a ratio. The same word is used with other references, which is why dB SPL, dBA and dBFS readings cannot be compared directly.
- "The scale stops at 100." It is not a percentage. Sirens reach 110 to 129 dBA and fireworks shows 140 dB or more.
To see the scale at work on real sound, start the decibel meter and clap once: the reading jumps by tens of decibels for an instant, which is a change in intensity of a thousandfold or more.
Sources
- HyperPhysics, Georgia State University: Sound Intensity and the decibel
- HyperPhysics, Georgia State University: Loudness and the rule of thumb for loudness
- US National Park Service: Understanding Sound
- Canadian Centre for Occupational Health and Safety: Noise, Basic Information
- NIDCD: Noise-Induced Hearing Loss (typical levels of everyday sounds)
- CDC/NIOSH: Noise-Induced Hearing Loss (3 dBA exchange rate)
- 29 CFR 1910.95 (140 dB peak sound pressure level for impulsive or impact noise)
Frequently asked questions
Is the decibel scale logarithmic?
Yes. A level in decibels is 10 times the base-10 logarithm of an intensity ratio. Each 10 dB increase is a tenfold increase in sound intensity, and each 20 dB increase is a tenfold increase in sound pressure.
Why is the decibel scale logarithmic and not linear?
The ear handles an enormous range: the intensity at the threshold of pain is about ten trillion times the intensity at the threshold of hearing. A logarithmic scale compresses that into roughly 0 to 130 dB and tracks perceived loudness better than a linear scale would.
How much louder is 10 dB?
Ten decibels is 10 times the sound intensity, but it is perceived as only about twice as loud. That figure is a rule of thumb, not an exact law.
What is 0 dB on the decibel scale?
0 dB SPL is a sound pressure of 20 micropascals, roughly the quietest 1,000 Hz tone a healthy young person can hear. It is a reference point, not the absence of sound, and negative values are possible.
Is 100 dB twice as loud as 50 dB?
No. 100 dB has 100,000 times the intensity of 50 dB and, by the rule of thumb of doubling every 10 dB, sounds about 32 times as loud.
What do two 60 dB sounds add up to?
About 63 dB. Decibels are added as energies, not as plain numbers, and doubling the energy raises the level by 3 dB.
Updated