What you need
Any device with a microphone can estimate sound level: a phone, a tablet, a laptop or a Chromebook. A browser meter such as our online decibel meter needs no installation. A handheld sound level meter is the better tool when the number matters, for example in a dispute or a workplace assessment. The method is the same for all of them; only the first steps differ.
On an iPhone or iPad (Safari)
- Open decibelmeter.io in Safari and tap Start.
- Tap Allow when Safari asks to use the microphone.
- Hold the phone with the bottom edge, where the main microphone sits, toward the sound.
If no prompt appears, microphone access for Safari has probably been set to Deny. Open the Settings app, find Safari's settings and change Microphone to Ask or Allow, then reload the page.
What about Apple's built-in features? The iPhone has no stand-alone meter for room noise. The Hearing control in Control Center shows a Headphone Level meter, which is the level of audio playing through your headphones, not the sound around you. Ambient noise is measured by the Noise app on Apple Watch, which uses the watch microphone, does not record or save any sound, and can notify you when the level passes a threshold you set. More in our decibel meter app guide.
On Android (Chrome)
- Open the meter in Chrome and tap Start.
- Choose Allow while visiting the site (or Allow this time).
- Point the microphone at the sound. On most phones it is a small hole on the bottom edge.
If you blocked the microphone earlier, open Chrome's More menu, then Settings, Site settings, Microphone. Find the site under Blocked, tap it and choose Allow. Android hardware varies more than iPhone hardware, which is why NIOSH has not verified its own sound level meter app for Android. Expect a larger error until you calibrate.
On a Windows PC, Mac or Chromebook
- Open the meter in your browser and click Start, then Allow.
- If nothing happens in Chrome, go to Settings, Privacy and security, Site settings, Microphone. The same screen lets you pick which microphone is the default.
- Check the operating system as well. On Windows 11: Settings, Privacy & security, Microphone, and make sure desktop apps may use the microphone. On a Mac: System Settings, Privacy & Security, Microphone, and switch on your browser.
A Chromebook works like Chrome on any other computer. Laptops add one problem of their own: the microphone sits next to the fan and the keyboard. Do not type during a measurement, and keep in mind that a busy fan raises quiet readings.
With a handheld sound level meter
- Check the calibration before you start, and again afterwards, if you have an acoustic calibrator.
- Set A-weighting and Slow response unless you have a reason to do otherwise. Workplace measurements are taken on Slow.
- Hold the meter at arm's length, at the ear height of the person exposed to the noise. Your body reflects and blocks sound, so keep it out of the way.
- Fit the windscreen outdoors or anywhere with moving air.
- Read the average. An integrating meter reports Leq, a single figure for sound that changes continually. With a basic meter, note the typical range and the maximum.
Meters are graded by accuracy. A Type 2 (Class 2) meter is considered accurate enough for workplace field measurements; Type 1 meters are mainly used for engineering, laboratory and research work.
Good measuring practice
- Measure where the ears are. The level drops with distance, by up to about 6 dB for each doubling of distance from a small source outdoors. A reading taken next to the machine does not describe the level at the desk. Always write down the distance.
- Use a sensible height. Ear height for a person; for outdoor environmental noise, about 1.5 m (5 ft) above the ground is the usual microphone position.
- Stay clear of large reflecting surfaces such as walls and windows unless that is where the listener is. Reflections add to the reading.
- Aim the microphone at the source and keep cases, fingers and fabric off it.
- Pick the weighting on purpose. dBA follows the ear's reduced sensitivity to bass and is what safety limits and most noise rules use. dBC is nearly flat; a dBC reading far above dBA means strong low-frequency content.
- Pick the time response. Fast (125 ms) follows speech and short events. Slow (1 s) gives a steadier number.
- Let it run and read Leq. Give steady sound at least 30 to 60 seconds, and sound that comes and goes several minutes. For hours of data, use the noise monitor.
- Measure the background too. Switch the source off, or wait until it stops, and measure again. If the background is 10 dB or more below the source, it adds less than half a decibel and can be ignored. If the two are within about 3 dB, you cannot separate them reliably.
- Calibrate. Matching your phone to a reference meter once removes most of the device-to-device error. See calibration.
Common mistakes
- Quoting the live number. It jumps several decibels a second. Report Leq and Max with the duration, for example "Leq 62 dBA over 10 minutes, max 78 dBA".
- Mixing weightings. A dBC reading cannot be compared with a dBA limit.
- Measuring in wind. Air moving across an unprotected microphone produces large false readings.
- Trusting very loud or very quiet readings from a phone. Phone microphones overload at high levels and show their own noise floor in very quiet rooms.
- Leaving call processing on. Noise suppression and automatic gain control change the level. Our meter asks the browser to turn them off and warns you if it cannot.
- Adding decibels like ordinary numbers. Two 60 dB sources make 63 dB, not 120. See the decibel scale.
- Treating a phone reading as official. It is an estimate. Our accuracy page explains the limits.
Sources
- Canadian Centre for Occupational Health and Safety: Noise, Measurement of Workplace Noise
- CDC/NIOSH: NIOSH Sound Level Meter App (accuracy and Android statement)
- Kardous CA, Shaw PB. Evaluation of smartphone sound measurement applications. J Acoust Soc Am. 2014
- Apple Support: Measure noise levels with Apple Watch
- Apple Support: Check your headphone audio levels on iPhone
- Google Chrome Help: Use your camera and microphone in Chrome
- Microsoft Support: Turn on app permissions for your microphone in Windows
- Apple Support: Control access to the microphone on Mac
- US Federal Highway Administration: Noise Measurement Handbook (microphone height, windscreen, calibration)
Frequently asked questions
Can an iPhone measure decibels?
Yes, with an app or a browser meter that uses the microphone. The iPhone has no built-in meter for room noise: the Hearing control in Control Center shows headphone audio level, and ambient noise measurement is a feature of the Noise app on Apple Watch.
How do I measure decibels on Android?
Open a browser decibel meter in Chrome, tap Start and allow the microphone. If the prompt does not appear, open Chrome's Settings, then Site settings, then Microphone, and allow the site.
How accurate is a phone at measuring decibels?
It varies by device. In NIOSH tests the best iPhone apps averaged within about 2 dB of a reference meter, while others were off by more than 10 dB. Calibrating against a handheld meter improves the result.
Should I measure in dBA or dBC?
Use dBA for comparisons with hearing-safety limits, noise rules and appliance ratings. Use dBC for bass-heavy sound such as music and engines, or to see how much low-frequency energy is present.
How long should I measure for?
At least 30 to 60 seconds for steady sound, reading the average (Leq) and not the flickering live number. For traffic, music or neighbor noise that comes and goes, measure for several minutes or longer.
What instrument is used to measure decibels?
A sound level meter. Workplace surveys use meters built to the sound level meter standards (Type or Class 2 or better), or noise dosimeters worn by the worker for a full shift.
Updated