Online Pitch Detector

Sing, hum or play a note and see its pitch in real time: the frequency in hertz, the nearest musical note, and a gauge that shows whether you are flat or sharp. It runs in your browser with your device's microphone.

--

-- Hz · --

Audio stays on your device. Nothing is recorded or uploaded.

What the pitch detector shows

How to find the note you are singing

  1. Press start and allow the microphone.
  2. Sing a steady "ah" or "oo" at a comfortable volume.
  3. Read the note name. If the gauge sits left of center you are flat, so raise the pitch slightly. If it sits right you are sharp.
  4. Watch the graph while you hold the note. A flat line is a steady pitch, a slope is drift, and a regular ripple is vibrato.

To practice matching pitch, play a note on the tone generator on another device, such as 440 Hz (A4), then sing it.

Reading cents

Musicians divide each semitone into 100 cents. The gauge shows your offset from the nearest note on that scale, so it never reads beyond about ±50 cents: past that point you are closer to the next note.

Within about 5 cents you are in tune for practical purposes. At 10 to 20 cents you are slightly off, and beyond 30 cents clearly out of tune. Nobody sings at exactly zero, and vibrato swings wider on purpose, so look at where the line centers, not at each wobble.

Finding your vocal range

Sing your lowest comfortable note and write down what the detector shows. Slide up to your highest comfortable note and do the same. The two notes are your range. The traditional choir voice types cover roughly these ranges:

Voice typeTypical rangeFrequency
BassE2 to E482 to 330 Hz
BaritoneA2 to A4110 to 440 Hz
TenorC3 to C5131 to 523 Hz
Alto (contralto)F3 to F5175 to 698 Hz
Mezzo-sopranoA3 to A5220 to 880 Hz
SopranoC4 to C6262 to 1,047 Hz

These are conventions, and real voices overlap them. Voice type also depends on where your voice sounds best, which a teacher judges by ear. Do not strain for extreme notes.

Tuning an instrument

The detector works for any instrument playing one note at a time. Play one string or note, let it ring, and adjust until the gauge centers on the note you want. For a guitar in standard tuning the open strings are E2, A2, D3, G3, B3 and E4.

It is a general pitch detector and not a dedicated guitar tuner. It shows the nearest note to whatever it hears and does not know which string you meant, so check the note name and octave as well as the gauge.

Standard pitch is A4 = 440 Hz (ISO 16). Set 415 Hz for Baroque pitch, 442 or 443 Hz to match many orchestras, or 432 Hz if you prefer that tuning.

How it works, and where it struggles

The tool uses autocorrelation. A pitched sound repeats its waveform many times per second. The detector compares a short slice of the microphone signal with delayed copies of itself and finds the delay at which the two line up best. That delay is the period of the note, and one divided by the period is the frequency. Because it looks for repetition and not the strongest peak, it works even when an overtone is louder than the fundamental.

The method has limits:

The pitch detector is a practice aid and cannot judge tone, timing or musicality.

Sources

Frequently asked questions

How do I find out what note I'm singing?

Allow microphone access, hold a steady note on a vowel such as "ah", and read the note name on the display. The cents gauge shows whether you are below (flat) or above (sharp) that note.

What does cents flat or sharp mean?

A cent is one hundredth of a semitone. If the gauge reads −20 cents, you are a fifth of a semitone below the nearest note. Within about 5 to 10 cents of zero sounds in tune to most listeners.

Can I use the pitch detector as a guitar tuner?

Yes, for a quick check. Pluck one string at a time and tune until the gauge centers on the right note. It is a general pitch detector, not a dedicated guitar tuner, so it does not know which string you intend and will simply show the nearest note.

Why does the reading jump around or show the wrong octave?

Pitch detection needs a clear, single, steady note. Background noise, breathy or very quiet singing, chords, and very low notes can all make the reading unstable or an octave off. Move closer to the microphone, find a quieter room and hold the note longer.

Can it detect chords or several notes at once?

No. It tracks one pitch at a time. With chords or several instruments it will show one of the notes or jump between them. To see all the frequencies in a sound, use the spectrum analyzer.

Can I change the reference pitch from 440 Hz?

Yes. The reference for A4 can be set anywhere from 415 Hz to 466 Hz, which covers Baroque pitch (415), 432 Hz tuning and orchestras that tune to 442 or 443 Hz.

Updated

Tools and guides