The short answer
A decibel is not an amount of sound in the way a kilogram is an amount of mass. It is a ratio: it says how much stronger a sound is than a reference value. For sound in air, the reference is a pressure of 20 micropascals, which is about the faintest 1,000 Hz tone a healthy young person can hear. That reference is 0 dB.
The name comes from deci (one tenth) and bel, a unit named after Alexander Graham Bell. That is why the B in dB is capitalized.
You can watch decibels change in real time with the online decibel meter.
Why decibels use a logarithmic scale
The ear handles an enormous range. The sound intensity at the threshold of pain is about ten trillion times the intensity at the threshold of hearing. Writing that range in ordinary units would be unworkable, so the decibel scale compresses it: each step of 10 dB multiplies the intensity by 10.
| Change in level | Sound intensity (energy) | Sound pressure | How it sounds |
|---|---|---|---|
| +1 dB | ×1.26 | ×1.12 | Barely noticeable, if at all |
| +3 dB | ×2 | ×1.41 | Noticeable |
| +6 dB | ×4 | ×2 | Clearly louder |
| +10 dB | ×10 | ×3.16 | About twice as loud |
| +20 dB | ×100 | ×10 | About four times as loud |
| +30 dB | ×1,000 | ×31.6 | About eight times as loud |
Two rules cover most everyday questions:
- +3 dB doubles the sound energy. This is why hearing-safety guidance halves the allowed exposure time for every 3 dB increase.
- +10 dB is ten times the energy, but sounds only about twice as loud. Loudness is a perception, and "twice as loud per 10 dB" is a rule of thumb, not an exact law.
The formulas
For sound pressure, which is what a microphone measures:
L = 20 × log10(p / p0), where p0 = 20 micropascals (µPa)
For sound intensity or power:
L = 10 × log10(I / I0), where I0 = 10^-12 watts per square meter
The factor is 20 for pressure and 10 for intensity because intensity is proportional to pressure squared. Both formulas give the same decibel value for the same sound.
Worked examples
1. From pressure to decibels
A sound with a pressure of 1 pascal: 20 × log10(1 / 0.00002) = 20 × 4.70 = 94 dB. That is roughly a gas lawn mower at the operator's position, and it is a standard level for sound calibrators.
2. Two equal sources
Two machines that each produce 90 dB do not make 180 dB. Twice the energy adds 3 dB, so together they produce 93 dB. Ten identical machines would add 10 dB, giving 100 dB.
3. Two unequal sources
Add an 80 dB machine to a 95 dB workshop and the total is still about 95 dB. When one source is 10 dB or more below another, it adds almost nothing. This is also why fixing the second-loudest noise in a room rarely helps.
4. Comparing two levels
How much more intense is an 85 dB sound than a 60 dB conversation? The difference is 25 dB, and 10^(25/10) ≈ 316 times the intensity. By the rule of thumb it sounds roughly five to six times as loud.
dB, dB SPL, dBA, dBC, dBZ and dBFS
"dB" alone only says "a ratio in decibels." The letters after it say what was measured and how. Mixing them up is the most common source of confusion.
| Unit | Reference or filter | Where you see it |
|---|---|---|
| dB SPL | Sound pressure level relative to 20 µPa | Acoustics, microphone and speaker specifications |
| dBA | SPL with A-weighting, which reduces low and very high frequencies to approximate human hearing | Hearing-safety limits (NIOSH, OSHA), noise ordinances, appliance ratings |
| dBC | SPL with C-weighting, nearly flat through the bass range | Peak measurements, music and low-frequency noise |
| dBZ | SPL with zero weighting: no frequency filter | Analysis and research |
| dBFS | Level relative to digital full scale; 0 dBFS is the maximum, so values are negative | Audio software, recording meters |
| dB HL | Hearing level relative to normal hearing at each test frequency | Audiograms and hearing tests |
dB vs dBA
Ears are less sensitive to low-pitched sound. A-weighting copies that by turning down the bass before the level is calculated: about 16 dB at 125 Hz and 26 dB at 63 Hz, with no change at 1,000 Hz. A rumbling truck engine can therefore read much lower in dBA than in dBC or dBZ, while a whistle reads about the same in all three. Health guidance uses dBA, so that is the default on our meter.
dBFS and how a phone becomes a decibel meter
A phone or laptop does not measure pressure directly. Its microphone signal arrives as digital samples, and software can only see how large they are relative to full scale, in dBFS. A reading of −40 dBFS could be a 50 dB room on one device and a 60 dB room on another, depending on microphone sensitivity.
To show dB SPL, a meter adds a calibration offset to the dBFS value. That is exactly what our tool does, and why readings are estimates until you set the offset against a known reference. See how to calibrate, how accurate the meter is and the methodology for the details.
Decibels in everyday terms
- 0 dB: threshold of hearing
- 30 dB: a whisper
- 60–70 dBA: normal conversation
- 85 dBA: the level where long or repeated exposure can start to damage hearing
- 110–129 dBA: sirens
- 120–130 dB: threshold of pain
The decibel chart lists more than 80 sounds with sources, and safe decibel levels explains how long you can be exposed at each level.
Sources
- HyperPhysics, Georgia State University: Sound Intensity and the decibel
- Canadian Centre for Occupational Health and Safety: Noise, Basic Information
- US National Park Service: Understanding Sound
- NIDCD: Noise-Induced Hearing Loss
- CDC/NIOSH: Noise-Induced Hearing Loss
- CDC/NIOSH: Understand Noise Exposure
- Sengpiel Audio: A- and C-weighting response table (per IEC 61672-1)
Frequently asked questions
What does dB stand for?
dB stands for decibel: one tenth of a bel, a unit named after Alexander Graham Bell. The B is capitalized because it comes from a person's name.
Is 0 dB complete silence?
No. 0 dB is the reference level, set near the quietest 1,000 Hz tone a healthy young ear can detect. Quieter sounds have negative decibel values.
What is the difference between dB and dBA?
dB is the general unit. dBA is a sound level measured with A-weighting, a filter that reduces low frequencies to approximate how human hearing responds. Hearing-safety limits are stated in dBA.
Is 100 dB twice as loud as 50 dB?
No, far more. 100 dB has 100,000 times the sound intensity of 50 dB. Using the rule that each 10 dB sounds about twice as loud, it is perceived as roughly 32 times as loud.
How many decibels is twice as loud?
About 10 dB more sounds twice as loud to most listeners. Doubling the sound energy itself only adds 3 dB, which is a small but noticeable change.
Why does my recording software show negative decibels?
Recording software uses dBFS, decibels relative to digital full scale. 0 dBFS is the loudest value the system can represent, so every real signal sits below it and reads negative.
Updated