How to use the headphone test
- Set the volume low before you put the headphones on. Each sound starts quiet and fades in. Raise the volume slowly to a comfortable level.
- Left and right. Press Left: the chime should play only in your left ear. Press Right, then Both. Both should sit in the middle of your head. Switch to pink noise if you want to compare how loud each side is.
- Stereo phase. Press In phase, then Out of phase, and compare.
- Frequency range. Press High end. A tone rises from 8 kHz towards 20 kHz. Press I can't hear it any more the moment it disappears. Then do the same with Low end, which falls from 200 Hz to 20 Hz.
- Bass check. Play 30, 40, 60 and 100 Hz in turn.
- Pan test. Left → right glides the sound between your ears. 3D circle moves it around your head.
How to read the results
Left and right
Each side should play on its own, and both sides together should sound centered and equally loud. If they are swapped, check that the L earcup is on your left ear. If you hear the same sound in both ears whichever button you press, turn off mono audio. If one side is quieter, check the balance slider, then swap the earbuds between ears: if the quiet side follows the earbud, the problem is in the hardware. The speaker test lists the balance and mono settings for each system.
Stereo phase
In phase sends identical sound to both ears, so it sounds solid and centered. Out of phase flips one side, so the two partly cancel. In headphones that usually sounds diffuse, hard to place or outside your head, with less bass. If the two sound the other way around, one driver or cable is wired with reversed polarity. That happens with some home-made or repaired cables and adapters.
Frequency range
The number is the last frequency you heard at this volume, through these headphones, on this device. It depends on all three:
- Your hearing. The audible range is usually quoted as about 20 Hz to 20 kHz, but the top falls with age. In a study of healthy adults, about half of those in their 20s responded to 20 kHz, and none of those aged 51 to 60 did. Not hearing the top few kilohertz is common and normal.
- Your device. Browsers usually run audio at 44.1 or 48 kHz, which can carry tones up to about 22 or 24 kHz. If the browser reports a lower rate, the sweep stops below 20 kHz.
- The headphones. Drivers lose output at the extremes, and earbuds that don't seal lose low frequencies first.
Use it to compare two pairs of headphones or two devices at the same volume. It is not a hearing test and can't tell you anything about your hearing health. If you have noticed a change in your hearing, ringing in your ears or one side sounding duller, see a doctor or audiologist.
Bass
With a good seal, many headphones play 30 and 40 Hz audibly. Earbuds often get quieter at the lowest tones, and the result changes a lot with fit. If the bass vanishes, try a larger ear tip or press the earbud in gently. A buzz or rattle at one frequency points to a damaged driver or a loose part. The bass test has a full 20 to 200 Hz sweep and more fixed tones.
Pan test
Left → right changes the level of each channel, so the sound should glide smoothly with no jump or dead spot in the middle. The 3D circle uses your browser's binaural processing, which filters the sound with measured head-related transfer functions (HRTF). Most people hear it move across and around their head. Front and back are harder to tell apart than left and right, so don't worry if it seems to swing past rather than circle behind you.
Troubleshooting
- No sound at all: check that the headphones are the selected output device and that no other device is holding the Bluetooth connection. The sound test has a full no-sound checklist.
- Bluetooth earbuds play in one ear only: charge both earbuds, remove the headphones from your Bluetooth list and pair them again so both connect.
- Crackling or dropouts: with Bluetooth, move closer to the device and away from Wi-Fi routers. With a cable, wiggle the plug gently. If the crackle follows the movement, the cable or socket is worn.
- Sound goes dull during calls: many Bluetooth headsets switch to a lower-quality mode while the microphone is in use. Close calling apps and reconnect.
Listen at moderate levels. Headphones put the sound directly into your ears, and long sessions at high volume can damage hearing. See safe decibel levels.
Sources
- HyperPhysics, Georgia State University: Sensitivity of human ears (audible range about 20 Hz to 20 kHz)
- Wang M et al. Extended high-frequency audiometry in healthy adults with different age groups. Journal of Otolaryngology – Head & Neck Surgery. 2021;50:52
- MDN: BaseAudioContext.sampleRate
- MDN: PannerNode.panningModel (HRTF rendering with measured impulse responses)
- Microsoft Support: Fix Bluetooth audio only playing in one channel
- Sound & Vision: How do I diagnose phase problems in my system?
- WHO: Deafness and hearing loss, safe listening
Frequently asked questions
How do I test my headphones online?
Put the headphones on with the volume low, press Left and Right to check that each side plays on its own, then run the phase, frequency range, bass and pan tests on this page. Each test takes under a minute.
Why do I hear the left channel in both ears?
Mono audio is probably turned on in your device's accessibility settings, which sends the same sound to both sides. Turn it off and keep the balance slider centered. A single Bluetooth earbud connected on its own also plays everything in one ear.
What does the frequency range result mean?
It is the last frequency you heard at the current volume through these headphones on this device. It mixes three things: the headphones, the device's audio output and your hearing. It is useful for comparing headphones or devices, but it is not a hearing test.
Why does the out-of-phase test sound strange?
Out of phase means one side plays the signal upside down. In headphones this usually sounds spread out, hard to place or as if it sits outside your head, with weaker bass. That is the expected result. If out of phase sounds more centered than in phase, one side is wired backwards.
Why is the bass weak in my earbuds?
Earbuds and in-ear headphones need a good seal to produce bass. Try a different ear tip size and push the earbud in a little further. Open-back headphones and loose-fitting earbuds naturally have less deep bass.
Does the 3D circle work on speakers?
It is designed for headphones. Binaural processing assumes each ear hears only its own channel, which speakers can't guarantee, so on speakers the movement is much weaker.
Updated