How to use the bass test
- Turn the volume down first. Deep bass can be much louder in the room than it sounds through a phone or laptop, and a subwoofer can move a lot of air. The test starts quiet and fades in.
- Press Play bass sweep. A single tone glides from 20 Hz up to 200 Hz. Choose 15, 30 or 60 seconds. Use the 60-second sweep when you are looking for rattles.
- Raise the volume slowly until the middle of the sweep, around 60 to 100 Hz, is clearly audible but not loud.
- Note what happens: where the tone first becomes audible, where it gets much louder or quieter, and any frequency where something buzzes.
- Use the fixed tones (20 to 200 Hz) to go back to a frequency that stood out. Press a tone again to stop it.
Turn on Pulse to switch the tone on and off twice a second. It makes it much easier to hear whether a buzz belongs to the tone or comes from somewhere else. Output sends the tone to the left, right or both channels.
How to read the results
How low your speakers go
The first frequency you can clearly hear is a rough low limit for your setup at that volume. Our ears are much less sensitive at low frequencies, so the bottom of the sweep always sounds quieter than it is. As a rough guide:
- Phone and laptop speakers usually stay silent for the first part of the sweep. That is a size limitation, not a fault.
- Bookshelf speakers usually come in somewhere in the middle of the sweep, depending on their size.
- A working subwoofer should make the lowest tones clearly audible, or at least felt.
Peaks and dips
A sweep through a real room is never perfectly even. Low-frequency waves bounce between the walls, floor and ceiling and create room modes, which make some frequencies boom and others almost disappear depending on where you sit. If one note booms, walk around the room while it plays: the level changes from place to place. Moving the subwoofer even half a meter, or moving away from a corner, often smooths the response.
Rattles and buzzes
Run the 60-second sweep with Pulse on and walk around. A buzz that stops with the tone is caused by the tone. Common culprits are loose screws in the speaker cabinet, a grille, a picture frame, a shelf, a window pane or objects on the subwoofer itself. Hold the suspect object with your hand while the tone plays: if the buzz stops, you have found it. A rough, crackling buzz that comes from the speaker itself at moderate volume can mean a damaged driver.
Subwoofer check
- Confirm it plays. Play 40 Hz. Put your hand on the subwoofer cabinet or listen close to it. If it is silent, check the power, the standby or auto-on setting, the cable from the receiver's subwoofer output, and that the subwoofer is enabled in your receiver or soundbar settings.
- Check the handover. Play the sweep and listen for a smooth transition between the subwoofer and the main speakers. A crossover of 80 Hz is the most common starting point and the THX standard. If your main speakers play deep bass cleanly, set the crossover about 10 Hz above the lowest frequency they handle well.
- Try the phase switch. Many subwoofers have a 0/180° phase switch or dial. Play 80 Hz (around the crossover) from your listening seat and flip it. Keep the setting that sounds louder and fuller there.
- Set the level by ear so the sweep doesn't jump in loudness when it moves from the subwoofer to the main speakers.
Some systems only send bass to the subwoofer from movies with a dedicated low-frequency channel, or only when the main speakers are set to Small. If the sub stays silent on this test but works with films, check the bass management settings on your receiver.
Troubleshooting
- No bass at all on headphones: check the fit. Earbuds without a seal lose almost all deep bass.
- Bass much weaker on one side: run the speaker test polarity check. A speaker wired backwards cancels bass.
- The tone distorts: lower the volume. Most small speakers distort at the bottom of their range long before they get loud.
- Want to see the response: play the sweep and watch it on the spectrum analyzer on a second device. Phone microphones are less sensitive to deep bass, so treat the lowest readings as rough.
For the full range from 20 Hz to 20 kHz, use the sound test. For a single tone at any frequency, use the tone generator.
Sources
- HyperPhysics, Georgia State University: Equal loudness curves (the ear discriminates against low frequencies at low levels)
- Sonarworks: Room modes
- SVS: Tips for setting the proper crossover frequency for a subwoofer (80 Hz, THX standard; about 10 Hz above the speakers' limit)
- Knowles: Frequency response and latency of MEMS microphones (low-frequency roll-off)
- Sound & Vision: How do I diagnose phase problems in my system?
Frequently asked questions
How do I test my bass online?
Turn the volume down, press Play bass sweep and raise the volume slowly. Note where you first hear the tone, listen for rattles and big jumps in loudness, then use the fixed tones to check any frequency that stood out.
Why can't I hear 20 Hz?
Most phone, laptop and small desktop speakers can't reproduce it, and human hearing is much less sensitive at very low frequencies, so 20 Hz needs far more level than mid tones to be heard. With a capable subwoofer you may feel it more than hear it.
What crossover should I set my subwoofer to?
80 Hz is the most common starting point and the THX standard. If your main speakers are small, a higher setting can help; if they play deep bass cleanly, set it about 10 Hz above the lowest frequency they handle well. Then use the sweep to check for a smooth handover.
Why is the bass loud at one frequency and weak at another?
Usually it's the room. Low-frequency sound waves reflect between walls, floor and ceiling and create room modes: peaks where they add up and dips where they cancel. Moving the subwoofer or your listening seat changes them.
Can a bass test damage my speakers?
It can if you play long, loud low tones. Keep the volume moderate and stop if you hear a slapping, crackling or bottoming-out sound, or see a woofer cone moving a lot.
Does the bass test work with headphones?
Yes. Headphones with a good seal often play lower than small speakers. Keep the volume low, because deep tones can be louder than they sound.
Updated