How to use the sound test
- Turn the volume down first. Every sound starts quiet and fades in, but your device volume decides how loud it ends up.
- Press Play test sound. A short chime repeats every two seconds on both channels. Raise the volume until you hear it at a comfortable level.
- Press Left, then Right. The chime should move to one side only. Both should sound as if it comes from the middle.
- Play the sweep. A single tone glides from 20 Hz up to 20 kHz. Pick a length of 10, 20 or 40 seconds. The longer sweeps give you more time to notice where the sound fades or rattles.
- Play the volume steps. Pink noise plays five times, each step 10 dB louder than the last, ending at your volume setting.
Switch the signal to Pink noise if the chime is hard to place. Pink noise has equal energy in every octave, so it covers the whole range at once and makes it easier to tell which speaker is playing.
How to read the results
Channel check
Left should come only from the left speaker or earbud, and Right only from the right. If both sides play when you press Left, your device is probably set to mono audio. If the sides are swapped, check the L and R markings, the speaker positions or the plugs. The speaker test has the menu paths for balance and mono audio on Windows, macOS, iPhone and Android.
Frequency sweep
The tone moves slowly at first and then seems to speed up, because each octave gets the same time. On most setups you will hear it come in somewhere between 20 and 100 Hz and fade out somewhere at the top. What to listen for:
- Where the low end comes in. Phone and laptop speakers are too small to play the deepest tones, so the start of the sweep is often silent on them. Use the bass test for a closer look at 20 to 200 Hz.
- Where the high end fades. The human hearing range is usually given as about 20 Hz to 20 kHz, but the top end falls with age. In one study of healthy adults, about half of people in their 20s heard 20 kHz, while nobody aged 51 to 60 did. Losing the last part of the sweep is normal.
- Rattles, buzzes and gaps. A buzz at one frequency usually means a loose part, a rattling shelf or a damaged driver. A sudden gap or a big jump in loudness can point to a crossover or tweeter problem, or, at low frequencies, to your room.
Volume steps
You should hear all five steps. If the first one or two are silent, your volume is very low. If the last step crackles, distorts or makes something rattle, your speakers or amplifier are at their limit at that setting. Lower the volume or the slider and try again.
No sound at all? Check these
- Output device. Your computer may be sending audio to another device, such as a monitor, a TV over HDMI or headphones that are switched off. On Windows 11, open Settings > System > Sound and choose the output. On a Mac, open System Settings > Sound > Output.
- Mute and volume. Check the volume keys, the mute key, the volume knob on the speakers and the power switch on powered speakers.
- Muted tab. Browsers can mute one site. In Chrome and Edge, right-click the tab and choose Unmute site if it is muted.
- Bluetooth. Wireless headphones may still be connected to your phone or another computer. Disconnect them there, or pick them again in your Bluetooth list.
- Silent mode on iPhone. If you hear nothing on an iPhone, turn silent mode off and try again.
- Another app. Some music and call apps take over the audio device. Close them and reload this page.
- Try another output. Plug in headphones or use the built-in speakers. If one works and the other doesn't, the problem is in that device or its cable.
Sound works, but something is off
- One side quiet or missing: use the headphone test or the speaker test and check the balance slider.
- Thin sound with no bass: run the bass test. With desktop speakers, also try the polarity check on the speaker test.
- Your microphone is the problem, not the speakers: the mic test shows the input level and lets you record and play back a short clip.
- You want a single frequency: the tone generator plays any tone from 20 Hz to 20 kHz.
Keep listening levels moderate. Long sessions at high volume through headphones can damage hearing over time. See safe decibel levels.
Sources
- HyperPhysics, Georgia State University: Sensitivity of human ears (audible range about 20 Hz to 20 kHz)
- Wang M et al. Extended high-frequency audiometry in healthy adults with different age groups. Journal of Otolaryngology – Head & Neck Surgery. 2021;50:52
- Live Science: What is pink noise? (equal energy per octave)
- Microsoft Support: Fix Bluetooth audio only playing in one channel (balance, mono audio)
- Apple Support: Change the sound output settings on Mac
- WHO: Deafness and hearing loss, safe listening
Frequently asked questions
How do I test if my sound is working?
Turn the volume down, press Play test sound and raise the volume slowly until you hear a repeating chime. If you hear it, the browser, the operating system and your speakers or headphones are all working. Then press Left and Right to check each side.
Why can't I hear anything?
The most common causes are the wrong output device, a muted device or browser tab, the volume at zero, or Bluetooth headphones connected to another device. On an iPhone, also check that silent mode is off. The checklist on this page goes through each one.
What is an audio test sweep?
A sweep is a single tone that glides from a low to a high frequency, here from 20 Hz to 20 kHz on a logarithmic scale, so each octave gets the same time. It shows where your speakers start and stop producing sound and reveals rattles, buzzes and dropouts.
Why does the sweep go silent before 20 kHz?
Three things limit the top of the range: your speakers or headphones, your device's audio output, and your hearing. The highest frequency people can hear falls with age, so many adults stop hearing the sweep well before 20 kHz. That is normal and not a fault in your speakers.
Is this a hearing test?
No. Your device, speakers, room and volume setting all change what you hear, so the result cannot measure your hearing. If you notice a change in your hearing, see a doctor or audiologist for a proper test.
Does the sound test work on a phone?
Yes. It runs in Safari, Chrome, Firefox and Edge on phones, tablets and computers. Sound only starts after you tap a button. Phone speakers can't play deep bass, so expect the low end of the sweep to be silent on them.
Updated